Applications
DirectVent Pro is a unitized, coaxial (concentric) venting system designed for use with direct vent gas or propane stoves, heaters, and fireplaces.
Materials and Construction
.020" aluminum inner wall. .018" galvanized steel outer wall. Painted outer walls made of laserwelded .018" galvalume steel. Caps also available in stainless steel and copper. Outer pipe brings combustion air to the appliance. Inner pipe exhausts flue gases to the outside. Gaskets or sealants not required (unless specified by the appliance manufacturer).
Clearances
Specified by the appliance manufacturer.
Diameters
4" x 6 5/8" and 5" x 8".
Listings
DirectVent Pro, in combination with the gas appliance, has been tested and listed as a decorative gas appliance system or as a direct vent heater system by a major testing agency, such as UL, CSA, Warnock Hersey, or OMNI. Check with your appliance manufacturer for approval.
Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation.
![Typical Installations For DuraVent Pro](/uploads/images/DuraVent_Pro-web.jpg)
More Typical Installations:
![DirectVent Pro Typical Installations](/uploads/images/DirectVent_Pro_installation.jpg)
Installation Key |
1 | Vertical Termination Cap |
2 | Storm Collar |
3 | Flashing |
4 | Cathedral Ceiling Support Box |
5 | Pipe |
6 | 45° Elbow |
7 | Class A Chimney Conversion Kit |
8 | 4" Flex |
9 | 90° Elbow |
10 | Horizontal Termination Cap |
11 | Snorkel Termination Cap |
12 | Colinear Kit |
13 | 3" Flex |
14 | Co-Axial to Co-Linear Connector |
15 | Masonry Chimney Conversion Kit |
16 | Elbow Strap |
Planning Your Installation:
1 | For vertical gas stove installations, measure the height from the stove outlet to the ceiling to determine the length of black pipe required. Select a ceiling support/wall thimble cover or a cathedral ceiling support box. |
2 | To determine the length of galvanized pipe required, measure the ceiling thickness and the vertical rise in an attic or second story. Firestops are required at each floor level beyond the first floor ceiling support/wall thimble cover or cathedral ceiling support box. If an offset is required to avoid obstructions, use a pair of 45° elbows. For proper support, use elbow straps with offsets. Use wall straps for long vertical runs. Attic Insulation Shield is required in attic. |
3 | Measure the roof pitch. Select the proper flashing and storm collar. Determine the minimum height above the roof. |
4 | For horizontal installations, check the appliance manufacturer’s instructions for minimum rise and maximum horizontal run. A snorkel termination may be used if height restrictions prevent adequate rise above the appliance. Select the appropriate Horizontal Termination Cap (see appliance manufacturer installation instructions). To protect vinyl siding, select vinyl siding standoff. Check appliance manufacturer’s instructions for wall thimble and firestop requirements. |
Design Recommendations
- The following design recommendations are general guideline to assist in the design and selection of venting components for your installation. Always follow DuraVent Installation instructions enclosed with the cap or support box before installing your chimney system. Installation instructions can be viewed online at www.duravent.com, under Catalogs and Instructions. Important: Check the manufacturer's rating plate and instruction manual to confirm that the DuraVent direct vent system is approved for use on the brand name appliance you have selected.
- The inner and outer pipe diameters should match the outlet size of the appliance.
- Check the appliance manufacturer's installation instructions to confirm which types of vent configurations are permitted (i.e. horizontal, vertical, chimney reline, etc.). Also, check for any venting restrictions such as maximum horizontal run, minimum and maximum vertical rise, maximum offset, etc.
- Be fire safe! Maintain at least the minimum clearances (air-space) between the vent pipe and nearby combustibles, as specified in the appliance manufacturer’s installation instructions. Use proper support and bracing. Follow local building codes and have your venting system inspected.